Photoinitiated curing of mono‐ and bifunctional epoxides by combination of active chain end and activated monomer cationic polymerization methods

Photoinitiated cationic polymerization of mono‐ and bifunctional epoxy monomers, namely cyclohexeneoxide (CHO), 4‐epoxycyclohexylmethyl‐3′,4′‐epoxycyclohexanecarboxylate (EEC), respectively by using sulphonium salts in the presence of hydroxylbutyl vinyl ether (HBVE) was studied. The real‐time FTIR spectroscopic, gel content determination, and thermal characterization studies revealed that both hydroxyl and vinyl ether functionalities of HBVE take part in the polymerization. During the polymerization, HBVE has the ability to react via both active chain end (ACE) and activated monomer mechanisms through its hydroxyl and vinyl ether functionalities, respectively. Thus, more efficient curing was observed with the addition of HBVE into EEC‐containing formulations. It was also demonstrated that HBVE is effective in facilitating the photoinduced crosslinking of monofunctional epoxy monomer, CHO in the absence of a conventional crosslinker. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4914–4920, 2007     

高固体分羟基丙烯酸树脂的合成

以过氧化二苯甲酰（BPO）／过氧化二异丙苯（DCP）（质量比为2：3）为复合引发剂，二甲苯为溶剂，选用适量含羟基单体和分子量调节剂，以减缓树脂合成聚合反应中的自动加速现象，合成了分子量为3000-4000，多分散性指数d〈2的高固体分羟基丙烯酸树脂．该树脂与缩二脲多异氰酸酯（HDI）的配漆实验证明，所得漆膜鲜映性好、丰满度高、色泽好、雾影值低、综合性能较好．     

含氰基的酚醛树脂及其碳纤维复合材料

含氰基的酚醛树脂，具有优异的耐高温性能和高温下的机械强度，在３１５℃下性能变化甚小；不着火，发烟量低，有良好的加工成型性能。热固化过程中氰基成三嗪环而交联，没有小分子脱出，是一类具有广泛发展前景的新型热固性树脂。     

Carbon–epoxy composites based on fibers coated with nylon 6,6: hygrothermal ageing versus interlaminar shear strength

Carbon fibers were coated in situ with a thin film of polyhexamethylene adipamide by an interfacial polycondensation technique. The modified fibers were used for the preparation of epoxy-based unidirectional composites. Specimens of these materials were immersed in water until equilibrium conditions were attained. The weight gain at equilibrium was determined as a function of the immersion temperature, the fiber volume fraction and the polyamide content deposited on the fibers. Water penetration in specimens made with uncoated carbon fibers increases when the volume fraction decreases. Introduction of the polyamide interlayer initially increases the water absorption, but reduces it at higher immersion temperatures and/or higher polyamide contents. The treated specimens were subjected to the short beam test to determine the interlaminar shear strength (ILSS). The data show that the ILSS decreases with water penetration but increases when the immersion temperature increases from 40 to 70°C. The overall performance encountered is discussed in terms of the possible roles of the polyamide interphase while taking into account mechanisms concerned with matrix plasticization, interphase degradation and residual stress relaxation.     

Dynamic mechanical analysis

Using dynamic mechanical analysis (DMA) we have studied thermal degradation for a system containing a diglycidyl ether of bisphenol A (DGEBA) and 1,3-bisaminomethylcylohexane (1,3-BAC). The changes of dynamic mechanical properties during thermal degradation indicated a shift of the glass transition temperature (T _g) to higher temperatures and a decrease in the peak value of the dynamic loss factor (tan δ) with an increasing of aging time. The value of dynamic storage modulus (E′) at the rubbery state showed an increase with aging time, whiteE′ at the glassy state only underwent a moderate change with increased thermal degradation. From these results it can be argued that thermal degradation during the stage prior to the onset of the severe degradation involves structural changes in the epoxy system, as further crosslinking and loss of dangling chains in the crosslinked network.     

Fracture strength of class II slot cavities restored with polymerizable restorative materials

This study compared the fracture strength of Class II slot cavities restored with polymerizable restorative materials. Sixty, caries-free, posterior teeth were divided into five groups of 12 teeth. The Class II slot cavities were prepared. The teeth were restored with two packable composites (Filtek P60, Surefil), a microhybrid composite (Filtek Z250)and two ormocer (Definite, Admira). The restorations were then subjected to fracture resistance tests. The marginal ridges of the restorations were loaded at an angle of 13.5° to the long axis of the tooth in an Universal Testing Machine until failure. Analysis of mean forces indicated that, Filtek P60, Surefil and Filtek Z250 exhibited better performance than Definite and Admira. The tested resin composites differed in their mechanical properties. This study suggested that fracture behavior were highly influenced by the filler system. Overall, Filtek P60, Surefil, Filtek Z250, demonstrated good fracture resistance. Copyright © 2003 John Wiley & Sons, Ltd.     

Determination of the rheological behavior of epoxy–amine thermosets by dynamic mechanical analysis: Isothermal methods versus nonisothermal methods

The reticulation process of an epoxy resin using an amine as a cure agent was studied at different temperatures and concentrations of the cure agent with dynamic mechanical thermal analysis. The study was performed under both isothermal and nonisothermal conditions, and a temperature–time–transformation diagram was obtained. The measurements from the two modes gave similar results, although the nonisothermal mode required fewer experiments. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1965–1977, 2003     

Synthesis and properties of thermosetting polymers from a phosphorous‐containing fatty acid derivative

A new phosphorous‐containing fatty acid diepoxide was obtained from 10‐undecenoyl chloride and 10‐(2′,5′‐dihydroxyphenyl)‐9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide and crosslinked with 4,4′‐diaminodiphenylmethane and bis(m‐aminophenyl)methylphosphine oxide. The properties of the thermosetting materials were evaluated by differential scanning calorimetry, dynamic mechanical thermal analysis, thermogravimetric analysis, and limiting oxygen index (LOI). Thermal and thermooxidative degradation was studied by gas chromatography/mass spectrometry, FTIR, ³¹P magic angle spinning NMR spectroscopy, and scanning electron microscopy. LOI values indicate good flame‐retardant properties that are related to the formation of a protective phosphorous‐rich layer that slowed down the degradation and prevented it from being total. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5630–5644, 2006     

Synthesis and cationic photopolymerization of new fluorinated,polyfunctional propenyl ether oligomers

New fluorinated, polyfunctional propenyl ether functionalized resins were synthesized, and their behavior in cationic photopolymerization was investigated. The photopolymerization proceeded efficiently with a high double‐bond conversion (>90%), giving rise to UV‐cured coatings characterized by low glass‐transition temperatures (?33 °C ≤ glass‐transition temperature ≤ ?15 °C) and hydrophobic surface properties. A fluorinated additive was also employed as a reactive additive in the cationic photopolymerization of trimethylolpropane tripropenyl ether, increasing the double‐bond conversion, polymer network flexibility, thermal stability, and surface hydrophobicity. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6943–6951, 2006     

N,N‐dimethylaminopyridine as initiator in the copolymerization of diglycidylether of bisphenol A with six‐membered cyclic carbonates

N,N‐Dimethylaminopyridine (DMAP) was used as initiator to cure mixtures of diglycidylether of bisphenol A (DGEBA) and 1,3‐dioxan‐2‐one (TMC) or 5,5‐dimethyl‐1,3‐dioxan‐2‐one (DMTMC). The curing was studied by differential scanning calorimetry (DSC) and Fourier transform infrared in the attenuated‐total‐reflection mode (FTIR/ATR). FTIR/ATR was used to monitor the competitive reactive processes and to quantify the evolution of the groups involved in the curing. We observed the formation of five‐membered cyclic carbonates and anionic carbonate groups that remain unreacted at the chain ends. The formation of these groups was explained by the attack of the anionic propagation species on the methylene carbon of the carbonate group, which leads to an alkyl‐oxygen rupture. By performing the cure in the thermobalance we could evaluate the loss of CO₂ produced in the samples containing carbonates. The kinetics were studied by DSC and analyzed with isoconversional procedures. The addition of carbonates slows down the curing rate. Thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA) experiments were used to evaluate the properties of the materials obtained. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2873–2882, 2006